- C4 Won't hold 2nd gear manually
- C-4 bit it Saturday night
- Long slip yoke in C4 truck tranny, why?
- valve bodys
- no high gear or reverse
- One more bellhousing question
- Thrust bearing diagram with notations
- Just started a online junkyard!
- 1st rebuild. I've done some research, few questions...
- Selective snap rings
- C4 identification
- vehicles with c4?sorry i tried to search
- \'67-\'69 valve body break down
- keep 67 c-4 or get 70-later
- Junkyard score
- Firm Shifts are Gone
- transmission shifts before I come to a stop
- C4 question
- transmission battle(I\'m losing)
- casting numbers or tags, what to trust?
- Fluid leaking from Trans Vent
- \"R\" servo
- R or H servo for rebuild? (with pic & web page)
- BYPASSING VAC MODULATOR??
- C-4 teardown
- C4 and C5 crossbreeding... Whats the best mix?
- I wish
- transmission problem
- no drive gear. help!
- Int. servo spring.
- C4 numbers
- Not Shifting
- Id help on a c4
- trans wont go into park?
- no auto shifts, no 3rd
- 157t vs 164t and which tranny
- Clutches, C4 vs AOD in a C4 drum. Pictures!
- converting my c4 into a 4x4 c4
- C4 pump and C6 bushing, how deep?
- Input Shell drilling question
- vacuum mod adj
- Clutches and steels, how to fit them.
- where to get c-4 parts
- \"ridgid bands\"
- C-4 In A 4WD '74 Bronco, Which Case?
- band strut????
- C4 spitting fluid out of dipstick
- anyone struck this problem??
- C4 wont shift into 3rd
- C4 Tailhousings
- Plugging the vent hole
- vent location
- How is it done? DIY reverse-pattern valve body
- C4 apart- Good news, but where to look for 2-3 flare
- Clarification on rev/high drum drilling and a couple of others
- test drive
- Direct Drum mod / direct drum tool
- what do you think
- \'64 valve body question.
- What a hassle - front pump
- removing the guts
- yellow stripe or green stripe vac mod??
- C4 newby question
- roller fwd planetary
- Band replacement?
- C4 swap with FMX flexplate....
- Purchasing ALTO 6 clutch kit..Best place???????
- No 1-2 at WOT
- C5
- raising ship point
- C-4 Endplay question
- roller no 3 and no 10?
- teflon rings
- smooth frictions in high/rev?
- What C5 can be used??
- No9 Mod (what size?)
- C4 kickdown lever question....
- Manual VB
- 1986 C5: Rolling up to a stop trans clunks as it downshifts?
- C4 rebuild
- Awesome Forum!!!!
- Front pump mod C4/C5
- Forward Drum Clutch Clearance
- kick down valve
- C4/C5
- c4 square seal vs c5 lip seal
- What year C4
- Is it right this c-4
- Need hints on high/rev clutch problem
- what parts to use?
- 5 or 6 bolts ?
- Torque converter and oil pump stator
- Drums, steels, & clutches
- where to buy extra clutches and steels?
- Fluid
- Help with no 1-2 shift under wot
- Clutches: C4 vs AOD vs C6 pic
- Number crunching the drums
- leaking from pan
- Can\'t get bore pin out of upper valve body
- No C6 forum so I\'ll try here. 462 Mel C6?
- Roller thrust fascination
- C4 won\'t move!
- Help Identify
- slow 2-3 shift
- My C-4 is ready to go
- Overfull C4 causing delayed shifting?
- Typical C4 Power Loss?
- air testing a C4?
- t-brake valvebody doing something funny!!
- Tranny Pan leaks!
- 65 C4
- Trans-go kit and slow 2-3 shift
- C4 filter
- Swapping from 24 to 26 spline shaft
- 2-3 SHIFT WITHOUT SHIFTING???
- What trans fluid in modified C-4
- 2-3 shift flare big time
- Modified Servo????
- Hey Ma' look what I made!
- Info about Cheetah
- ultimate C-4 finally finished
- Servo Return springs?
- c- 4 p/a planatery
- Stuck input shaft (C4)
- Differences between 6 cyl. and V8 C4's
- No Reverse
- snap ring help
- C-4 poll, what happened?
- 1-2 flare
- C 4 block plate
- help
- help
- Governor removal..
- ? about front clutch hub and ring gear
- C-4 questions
- C4 slow to engage in reverse
- 66 C 4 ****ft kits
- do I have an oddball c4 bellhousing
- C4 Shifts from 2nd to drive on it\'s own?
- \'75 C4 band tightening
- Does anyone offer a 3:1 first gear planetary set?
- no reverse
- Really really need help with this (control valve assembly)
- C4 PUMPS
- Do I need a 28oz or 50oz flex plate?
- C4 slipyokes
- C6
- PA\'s Pro Pump any good ?
- leaking dip stick
- C4 Overheating
- Planetaries and pump pressure
- loosing oil from breather vent?
- What happens in a C4 if....
- C4 has no reverse when it wams up.(somebody please help)
- Need Bell to fit 69 C4 to 78 200 Six Cylinder
- C5 forward drum?
- C4 slow to or wont\'s shift into forward gears
- need some help (updated again, still problems)
- Shifts
- Intermediate band adjustment
- When looking for c4 tranny\'s?
- C-4 NO GO WHEN COLD --Need HELP !! SOMEONE!
- Bench test for valve body, clutches, etc?
- Vib. Dampner on C4....
- Police interceptor c4?
- Need Info On C-4 Trans
- front or back port
- What band to use ?
- C4 START UP PROBLEMS
- C4 has wierd reverse problem
- stall converter?
- C4 Not Shifting 1-2
- Problems with Dynamic C4 transmission
- stall converter question
- What would happen if...
- Valve Body Not Shifting
- Still no third (C4 gurus inside please!)
- Should the C4 kickdown valve spring be VERY resistant?
- No drop into 1st
- End play spec?
- ford c-4 help!!
- Question on a PA trans...
- C4 not Shifing
- What would happen if...
- C-4 Transmission fluid level question
- Transmission not down shifting.
- Why isn\'t Kickdown Necessary?
- 2nd to 3rd servo installation
- New Post Same Problem
- C4 SEEMS TO HIT REV LIMITER AT 3500 RPM WHAT GOING ON?
- SHIFTS HARD INTO 1ST TO 2ND BUT INTO 3 IT REVS HIGH AND GOES?
- Need the Governor?
- Anyone close want to tackle my C-4? DECISION MADE
- How to replace bigger diameter bushings?
- Do these parts look ok for 600hp?
- what do i need for my mustang.C4 trans. with a 1993 engine 5.0
- Anyone got instructions for DIY manual valve body mods
- c4 torque converter or not?
- Is is better to leave trans unpainted?
- Well, since mt new PA C-4 ain\'t here...
- C4-Can\'t get pump out
- What solvent do I use to clean internal C4 parts?
- C4 BAND ADJUSTMENT LOCATIONS?
- C4 BAND ADJUSTMENT LOCATIONS?
- C4 yoke
- front seal leak
- Worn thrust bearings
- Building a C4
- stall converter
- C4 Pump still TOTALLY stuck- help!
- Yet another no-shift
- PA Supercomp C4 ??? (Long)
- braided line fittings for C4
- input shaft help (have pics)
- tci strretfighter 3rd gear problem
- 3rd gear/ Valve Body question
- capacity,schmapacity
- 2-3 FLARE IS THIS BECAUSE I HAVE NO KICK DOWN LINKAGE?
- 6 friction direct/high
- Got aluminum..er STEEL.. in the pan - ideas?
- C4 and C6 side by side.
- New PA C-4 cam today... Now with pics!
- Transmission power loss figures
- No forward when hot??
- shaft length -or- damn, size does matter
- any chance a valve body may cause a 2 3 flare.
- C4 in Mustang much better now....maybe...maybe not...
- Converters
- transbrake
- C4 - which fitting is pressure side
- Bolt sealant
- Servos, Pump Filter, Cooler Lines, C-5 band adjustments, etc.
- rebuilt c4 no gears?
- FE engine to C4?
- C4 clutch drum steels question
- Cooler lines/speedometer gear questions
- in a jam
- identifying trans brake
- Identifying torque converter!
- i am having a problem with my car and i think it is the torque converter
- Setting end play with H-Gauge?
- Does PA 6 pinion planetary come with bearing?
- Converter to flexplate nuts...and alignment...help!!
- C4 TO 460 Bellhousing?
- New C4 installed but have no nuetral
- stupid bell housing question- well, no, not stupid bell housing, stupid question
- rebuilt C5 problems
- Need info re; JPT transmissions
- C4 Hard shift in to reverse