302 351W Miller 7075-T7 Aircraft Aluminum SBF Roller Rockers - Page 3

**paulkane** · 01-03-2008, 07:29 PM

Quote:

Originally Posted by Canuck

Hi!

Do you have anymore sets left?If you do I would love to purchase a set off of you!

Thanks,

Terry

Terry, we sure do, PM me or give me a call or email me (phone number and email via the link in my signature line below) and we'll work things out. If you are in Canada (judging by your username

), then yes we ship there. Also, we ship via USPS to Canada, charge the USPS shipping rate and nothing more.

Paul

**rcodenewf** · 01-04-2008, 08:07 AM

Hello Paul..what do you have for the 428 cj?

John

**h20craig** · 01-04-2008, 08:01 PM

Quote:

Originally Posted by paulkane

PRICE REDUCTION!

Miller 7075-T7 Aircraft Aluminum SBF Roller Rockers
For a limited time: $149/Set!

Miller SBF Roller Rockers (same manufacturer as the $2800 Miller Boss 429 hemi rocker arms)

Designed exclusively for small block Windsor motors (289, 302, 351W, etc.)

Rocker body made of 7075-T7 aircraft aluminum

8620 billet steel trunnion axle which is rifle drilled for additional strength

Dual trunnion flats (inverted trunnion at installation is impossible)

Beefy oversize pin on roller tip

Tiny pushrod cup oiling hole so as to help control top end oiling

Chromoly hammer-forged polylocks (ie work hardened, not broached)

Establishing proper pushrod length is a snap with the top measuring face on the rocker (instructions inlcuded).

Available in 1.6 ratio, 7/16" or 3/8" rocker stud

Originally $384 Retail/$310 Racer Net

Offered here at less than half price $149/set. Complete brand new rocker arm package with chromoly polylocks and instructions. Yes, we ship international.

We install the big block version on all of our ported D0VE head conversions with great success and 100% customer satisfaction. We don't think there's a better rocker arm package for the money, as none of the other rockers offered at this price come with comparable materials, composition or technology behind them, nor will you find any other roller rocker with a rocker body made of 7075-T7 aircraft aluminum, with anywhere near the fatigue / destruct / tensile strength capabilities and the 8620 billet steel rifle drilled trunnion, all for for just $149.

PM, call or email if interested,

Paul
www.highflowdynamics.com/
highflowdynamics@earthlink.net
(310) 435-1900

hi,would like to purchase two sets thanks , could u please give total cost to australia brisbane 4502 just normal cheap post thanks and also a secure way to pay thanks again.

**paulkane** · 01-04-2008, 08:18 PM

Quote:

Originally Posted by rcodenewf

Hello Paul..what do you have for the 428 cj?

John

John, I'd love to help ya; unfortunately all we have are 302-351W rockers for sale. All the BB rockers are gone...save for a few sets for use internally on our 429/460 engine builds (which are not 428FE applicable anyway).

Paul

**paulkane** · 01-04-2008, 08:30 PM

Quote:

Originally Posted by h20craig

hi,would like to purchase two sets thanks , could u please give total cost to australia brisbane 4502 just normal cheap post thanks and also a secure way to pay thanks again.

G'day mate! Yes, we ship down under.

The United States Postal Service (USPS) has stopped offering "surface shipments (by sea)" to Australia. Therefore, only Air Mail is available. The grand total (SBF rockers + shipping) for 2 sets shipped to Australia costs:

US$335 shipped via USPS Priority Mail "Flat Rate Box," or,
US$383 shipped via Priority Mail International (in our box).

Please note: The "Flat Rate Box" offered by the USPS (1st choice above) is constructed of a rather flimsy cardboard (in regards to holding a set of rockers) and leaves little room around the rockers for protective packing popcorn to be placed around the rocker set, while our 9"x9"x16" box (2nd choice above) allows for lots of protective packing around the rockers. So, should you cross your fingers with the Flat Rate box or spend the extra US$48 for the added protection with our box? The choice is up to you.

We can be paid via Paypal, in U.S. dolllars only. Please contact me via the email address below and we'll iron out the details.

Thanks,

Paul

email: highflowdynamics@earthlink.net

**paulkane** · 01-08-2008, 06:33 PM

R.T.: Your rockers shipped this morning.

J.S.: Your shipment will arrive tomorrow.

Thanks for your business gentlemen,

Paul

**rsalway** · 01-09-2008, 04:55 AM

How much to ship one set to 46733?

**paulkane** · 01-09-2008, 10:28 AM

Quote:

Originally Posted by rsalway

How much to ship one set to 46733?

rsalway,

We ship via Federal Express and charge a flat $11 shipped anywhere in the lower 48 states, which is a good deal for you because the FedEx website calculates $13.45 to ship a set from our zip code to yours. Grand total would be a mere $160 shipped.

Paul

**BIGJOE** · 01-09-2008, 01:23 PM

I received the rockerarms today and I am VERY impressed with the quality and workmanship, Thank again for your help with the shipping and so forth.
JOE SHERMAN RACING ENGINES

**dfree383** · 01-09-2008, 01:32 PM

Paul

Are the Miller Rockers avaliable in higher ratios? Like 1.8 , 1.9 or ratios over 2.0?



All content © FordMuscle, LLC. \| Ford® is a registered trademark of the Ford Motor Company. \| FordMuscle.com is not affiliated with the Ford Motor Company.